Car Stereo is the #1 Car Audio Online Resource for radio,speakers, MP3, amps, subwoofers, box enclosures, IASCA,DB Drag Racing, USACi and MECA events Car Stereo is the #1 Car Audio Online Resource
Car Stereo is the #1 Car Audio Online Resource
Car Stereo is the #1 Car Audio Online Resource Welcome to CarStereo.com the Internet Guide to Car Audio Car Stereo is the #1 Car Audio Online ResourceMY ACCOUNT   
Car Stereo is the #1 Car Audio Online Resource
Box Design Box Design
Amplifiers Amplifiers
Basic Electrical Basic Electrical
Car Audio Basics Car Audio Basics
Crossovers & Filter Calculator Crossovers & Filter Calculator
Equalizers Equalizers
Installation and Wiring Installation and Wiring
Source Unit Source Unit
Speaker Speaker
#CategoryName# Car Audio Terms
#CategoryName# Sub Box Design Software





OnlineCarStereo.com
The best and biggest selection of mobile audio/stereo, multimedia/navigation and accessories at the lowest prices! Kenwood, Pioneer, Rockford Fosgate, JVC, Sony, Clarion, Jensen, Infinity, Kicker and more...
Car Audio Black Friday Sales!
Share |


 

Sealed SPEAKER and Subwoofer SYSTEM DESIGN Tips

Sealed Speaker Enclosure Design

Explanation of Terms
Qts, Vas, and Fs, are the electro-mechanical parameters for your woofer. They are also commonly referred to as the "Thiele-Small" parameters. You can get these from the paperwork that came with your speakers, from the dealer where you purchased your speakers, or from the manufacturer of the speaker (they are sometimes hard to contact, however).

Qtc - is the total resonance of the speaker system. An enclosure with a Qtc value of 0.707 will give you the flattest frequency response and the lowest possible F3 for a given driver, use this value if you want the your music to sound as close to the original recording as possible.

 In the frequency response plot below, the relative efficiency of the speaker is 90 dB. So,   the frequency of F3 is determined by first finding the proper SPL (sound pressure level) to look at (90 dB - 3dB = 87 dB) on the left scale, and then following this line over to the right until you run into the frequency response plot (the colored lines) of the enclosure you are interested in. Then you draw a line from this point down to the bottom scale to find the frequency of F3.

Qtc comparison

 Most people like the sound of boxes designed with Qtc values ranging from 0.9-1.1 which produces a slightly emphasized bass range. Values above 1.2 are undesirable because they tend to sound unnatural (the peak around the 100 Hertz range in the plot above is what most people refer to as "boomy" sound), and they also can be physically hard on the speaker.

Important Qtc relationships :

 F3 increases for values above or below 0.707.
 Enclosure volume (Vb) requirements decrease with higher Qtc values.
 Mechanical power handling increases for Qtc values up to 1.1 .

 Mechanical power handling is not the same as the manufacturers' "power rating" (which only tells how much power the voice-coil can handle without burning up, and has nothing to do with how much input power the speaker can take before it bottoms out). The speaker's suspension and the enclosure design determine the mechanical power handling of the system.

Fc - the resonant frequency of the driver when mounted to an enclosure.
Vb - the required internal volume of the enclosure.
F3 - the frequency that the response is down (from the reference level) by 3 dB at. In the frequency response plot below, the reference level is 90 dB (left scale). So, the frequency (bottom scale) of F3 is at the intersection of 87 dB and 40 Hertz. Therefore, this enclosure design has an F3 of 40 Hertz.

2nd-Order Frequency Response Plot

 
Alpha - The Greek letter alpha. In speaker design, this term is used to reflect the ratio of speaker compliance (Vas) to enclosure volume (Vb).
Second-Order Speaker Enclosure Design Formulas
Sealed Enclosure Image
Typical Sealed Enclosure Design  
 The following formulas will allow you to design a sealed speaker enclosure for any Qtc value you desire.
Alpha= (Qtc / Qts)2 - 1
Vb = Vas / Alpha
Fc = (Qtc x Fs/ Qts
F3 Formula

 If you don't want to/can't calculate an enclosure using the formulas shown above, click here to use the Javascript calculator, which does all of the math for you.


 

 previous page Back Email this page to a Friend 
Home  |  Contact Us  |  About Us  |  Advertise  |  Car Audio How to Links  |  Join!  |  Log-In
 
Copyright © 2006 Online ConneXions Inc.
Web Designed & Hosting